Fuel Pump Circuit Troubleshooting

If you suspect a problem with the fuel pump, check that the fuel pump actually runs; when it is ON, you will hear some noise if you listen to the fuel fill port with the fuel fill cap removed. The fuel pump should run for 2 seconds when the ignition switch is first turned on. If the fuel pump does not make noise, check as follows:

1.Turn the ignition switch OFF.

2.Remove the fuse cover.

3.Remove PGM-FI main relay 2 (A) from the under-dash fuse/relay box.

 

4.Turn the ignition switch ON (II).

5.Measure voltage between PGM-FI main relay 2 4P connector terminal No. 3 and body ground.

 

Is there battery voltage?


YES - Go to 6.


NO - Repair open in the wire between PGM-FI main relay 1 and PGM-FI main relay 2.n

6.Measure voltage between PGM-FI main relay 2 4P connector terminal No. 1 and body ground.

 

Is there battery voltage?


YES - Go to 7.


NO - Repair open in the wire between the under-dash fuse/relay box and PGM-FI main relay 2.n


7.Turn the ignition switch OFF.

8.Disconnect ECM/PCM connector E (31P).

9.Check for continuity between PGM-FI main relay 2 4P connector terminal No. 4 and ECM/PCM connector terminal E1*1 (E10)*2.

 

Is there continuity?


YES - Go to 10.


NO - Repair open in the wire between PGM-FI main relay 2 and the ECM/PCM (E1*1 (E10)*2).n

10.Reinstall PGM-FI main relay 2.

11.Turn the ignition switch ON (II).

12.Measure voltage between ECM/PCM connector terminal E1*1 (E10)*2 and body ground.

 

Is there battery voltage?


YES - Go to 13.


NO - Replace PGM-FI main relay 2.n


13.Turn the ignition switch OFF.

14.Reconnect ECM/PCM connector E (31P).

15.Turn the ignition switch ON (II), and measure voltage between ECM/PCM connector terminal E1*1 (E10)*2 and body ground within the first 2 seconds after the ignition switch was turned ON (II).

 

Is there battery voltage?


YES - Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM, then recheck. If the symptom/indication goes away with a known-good ECM/PCM, replace the original  ECM/ PCM.n


NO - Go to 16.


16.Turn the ignition switch OFF.

17.Remove the access panel from the floor.

18.Measure voltage between the fuel pump 5P connector terminal No. 5 and body ground within the first 2 seconds after the ignition switch was turned ON (II).

 

Is there battery voltage?


YES - Go to 25.


NO - Go to 19.

19.Turn the ignition switch OFF.

20.Remove the fuse cover.

21.Remove PGM-FI main relay 2 (A) from the under-dash fuse/relay box.

 

22.Connect PGM-FI main relay 2 4P connector terminals No. 1 and No. 2 with a jumper wire.

 

23.Turn the ignition switch ON (II).

24.Measure voltage between fuel pump 5P connector terminal No. 5 and body ground within the first 2 seconds after the ignition switch was turned ON (II).

 

Is there battery voltage?


YES - Replace PGM-FI main relay 2.n


NO - Repair open in the wire between PGM-FI main relay 2 and the fuel pump 5P connector.n


25.Turn the ignition switch OFF.

26.Check for continuity between fuel pump 5P connector terminal No. 4 and body ground.

 

Is there continuity?


YES - Replace the fuel pump.n


NO - Repair open in the wire between the fuel pump 5P connector and G402.n