Skip to main content
DTC Troubleshooting: P0982 (60)

DTC P0982:
 Shift Solenoid Valve D (Short)
NOTE:
  1. Clear the DTC with the HDS.
  1. Start the engine in P, and wait for at least 1 second.
  1. Check that DTC P0982 recurs.
Is DTC P0982 indicated?
YES -
Go to Step 7 .
NO -
Go to Step 4 .
  1. Select Shift Solenoid D in the Miscellaneous Test Menu, and test shift solenoid valve D with the HDS.
Is a clicking sound heard?
YES -
Go to Step 5 .
NO -
Go to Step 7 .
  1. Start the engine in P, and wait for at least 1 second. With the brake pedal pressed, shift to N, and wait for at least 1 second.
  1. Monitor the OBD status for P0982 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.
Does the HDS indicate FAILED?
YES -
Go to Step 7 .
NO -
Intermittent failure, the system is OK at this time. Check the SH D wire for an intermittent short to ground between shift solenoid valve E and the PCM. If the HDS indicates NOT COMPLETED, return to Step 4 and recheck.
  1. Turn the ignition switch to LOCK (0).
  1. Jump the SCS line with the HDS.
  1. Disconnect PCM connectors B (49P) and C (49P).
  1. Measure the resistance between PCM connector terminals B12 and C44 or C48.
Is there less than 12 Ω?
YES -
Go to Step 11 .
NO -
Go to Step 16 .
  1. Disconnect the shift solenoid harness connector.

  1. Check for continuity between PCM connector terminals B12 and C44 or C48.
Is there continuity?
YES -
Repair short in the wire between PCM connector terminal B12 and the shift solenoid harness connector, then go to Step 21 .
NO -
Go to Step 13 .
Is shift solenoid valve D OK?
YES -
Go to Step 14 .
NO -
  1. Turn the ignition switch to ON (II).

  1. Measure the voltage between PCM connector terminals C10 and C44 or C48.
Is there battery voltage?
YES -
Go to Step 16 .
NO -
Check for a blown No. 20 (15 A) fuse in the under-dash fuse/relay box. If the fuse is OK, repair open or short in the wire between PCM connector terminal C10 and the under-dash fuse/relay box, then go to Step 21 .
  1. Reconnect all connectors.
  1. Start the engine in P, and wait for at least 1 second. With the brake pedal pressed, shift to N, and wait for at least 1 second.
  1. Check for Temporary DTCs or DTCs with the HDS.
Is DTC P0982 indicated?
YES -
If the PCM was updated, substitute a known-good PCM, then recheck. If the PCM was substituted, go to Step 1 .
NO -
Go to Step 20 .
  1. Monitor the OBD status for P0982 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.
Does the HDS indicate PASSED?
YES -
If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM. If any other DTCs were indicated on Step 19 , go to the indicated DTC's troubleshooting.■
NO -
Check for an intermittent short in the wire between shift solenoid valve D and the PCM. If the PCM was updated, substitute a known-good PCM, then recheck. If the PCM was substituted, go to Step 1 . If the HDS indicates NOT COMPLETED, return to Step 18 and recheck.
  1. Reconnect all connectors.
  1. Clear the DTC with the HDS.
  1. Start the engine in P, and wait for at least 1 second. With the brake pedal pressed, shift to N, and wait for at least 1 second.
  1. Check for Temporary DTCs or DTCs with the HDS.
Is DTC P0982 indicated?
YES -
Check for an intermittent short in the wire between shift solenoid valve D and the PCM, then go to Step 1 .
NO -
Go to Step 25 .
  1. Monitor the OBD status for P0982 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.
Does the HDS indicate PASSED?
YES -
Troubleshooting is complete. If any other DTCs were indicated on Step 24 , go to the indicated DTC's troubleshooting.■
NO -
Check for an intermittent short in the wire between shift solenoid valve D and the PCM, then go to Step 1 . If the HDS indicates NOT COMPLETED, return to Step 23 and recheck.