Skip to main content
SIL Troubleshooting

NOTE: Check for Temporary DTCs or DTCs with the HDS before doing this procedure. If any DTCs are indicated, troubleshoot them first, then do this procedure.
  1. Start the engine.
  1. Test-drive several minutes.
  1. Check the C SHAFT SPD in the DATA LIST with the HDS.
In any vehicle speed indicated?
YES -
Go to Step 5 .
NO -
Is the result OK?
YES -
Go to Step 6 .
NO -
Substitute a known-good gauge control module, and recheck. If the symptom/indication goes away with a known-good gauge control module, replace the original gauge control module.
Is the result OK?
YES -
Go to Step 7 .
NO -
Depending on the result, replace the appropriate part.■
Is the result OK?
YES -
Go to Step 8 .
NO -
Depending on the result, repair or replace the appropriate part.■
  1. Turn the ignition switch to LOCK (0).
Is a position proper?
YES -
Go to Step 10 .
NO -
  1. Turn the ignition switch to ON (II).
  1. Check CLUTCH PEDAL POSITION SWITCH A in the DATA LIST with the HDS.
Is OFF indicated?
YES -
Go to Step 12 .
NO -
Go to Step 28 .
  1. Press the clutch pedal.
  1. Check CLUTCH PEDAL POSITION SWITCH A in the DATA LIST with the HDS.
Is ON indicated?
YES -
Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the gauge control module, clutch pedal position switch A, and the ECM.■
NO -
Go to Step 14 .
  1. Turn the ignition switch to LOCK (0).
  1. Disconnect the clutch pedal position switch A 2P connector.
  1. Connect clutch pedal position switch A 2P connector terminals No. 1 and No. 2 with a jumper wire.
  1. Turn the ignition switch to ON (II).
  1. Check CLUTCH PEDAL POSITION SWITCH A in the DATA LIST with the HDS.
Is ON indicated?
YES -
NO -
Go to Step 19 .
  1. Turn the ignition switch to LOCK (0).
  1. Remove the jumper wire from the clutch pedal position switch A 2P connector.

  1. Connect clutch pedal position switch A 2P connector terminal No. 1 and body ground with a jumper wire.
  1. Turn the ignition switch to ON (II).
  1. Check CLUTCH PEDAL POSITION SWITCH A in the DATA LIST with the HDS.
Is ON indicated?
YES -
Repair open in the wire between clutch pedal position switch A and body ground (LHD model: G302, RHD model: G401).■
NO -
Go to Step 24 .
  1. Turn the ignition switch to LOCK (0).
  1. Jump the SCS line with the HDS.
  1. Disconnect ECM connector A (49P).

  1. Check for continuity between ECM connector terminal A48 and body ground.
Is there continuity?
YES -
Update the ECM if it does not have the latest software, or substitute a known-good ECM, then recheck. If the symptom/indication goes away with a known-good ECM, replace the original ECM.
NO -
Repair open in the wire between the ECM (A48) and clutch pedal position switch A.■
  1. Turn the ignition switch to LOCK (0).
  1. Disconnect the clutch pedal position switch A 2P connector.
  1. Turn the ignition switch to ON (II).
  1. Check CLUTCH PEDAL POSITION SWITCH A in the DATA LIST with the HDS.
Is OFF indicated?
YES -
NO -
Go to Step 32 .
  1. Turn the ignition switch to LOCK (0).
  1. Jump the SCS line with the HDS.
  1. Disconnect ECM connector A (49P).

  1. Check for continuity between ECM connector terminal A48 and body ground.
Is there continuity?
YES -
Repair short in the wire between the ECM (A48) and clutch pedal position switch A.■
NO -
Update the ECM if it does not have the latest software, or substitute a known-good ECM, then recheck. If the symptom/indication goes away with a known-good ECM, replace the original ECM.